Extron-electronics SME 100 User Guide Manuale Utente Pagina 25
- Pagina / 185
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
SME100 Network
Configuration
This section provides information on:
• Network Settings Configuration
• SME100 IP Addressing for Multiple Installations
• Protocols Used for Streaming
Network Settings Configuration
NOTE: See the "IP Addressing" section on page 166 for information on choosing
compatible network addresses.
The SME100 is pre-configured with the following network settings.
IP address: 192.168.254.254
Subnet mask: 255.255.0.0
Gateway: 0.0.0.0
The network settings of the SME100 can be reconfigured using the following methods.
• Front Panel Network Configuration — Use the "Edit Comm Settings Menu" (see
page 43); this is best used for new and existing network installations.
• Web-based User Interface Network Configuration (see page 85) — This type of
configuration is best used for new network installations that will be initially using the
pre-configured network settings, or for existing network installations where the
SME100 is properly integrated into a network.
NOTES:
• To configure the SME100 using the web-based user interface, the
SME100 must be connected to a network using compatible network settings.
A control PC (with compatible network settings) must also be connected to the
same network. The control PC uses the IP address of the SME100 to access
the web-based user interface.
• For information on how to obtain the current network settings of the SME100
using the front panel, see the "Comm Settings Menu" section on page 43.
SME100 IP Addressing for Multiple Installations
The default IP address and subnet mask is adequate for most installations. When multiple
SME100 devices are on the network, the IP address of each device must be different
to avoid conflicts and provide consistent communications with the control PC. Since the
default IP address of every SME100 is 192.168.254.254, it is recommended that the first
SME100 connected to the network change its IP address immediately. That always ensures
a previously installed SME100 will be "out of the way" when the next one is connected,
avoiding a conflict (see "IP Addressing" on page166 for information on choosing
compatible network addresses).
SME100 • Network Configuration 19
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Prodotti e manuali riguardandi Hardware Extron-electronics SME 100 User Guide
(2 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale