Extron-electronics CS 120P Setup Guide Manuale Utente Scaricare il pdf (Pagina 1)

CS 120P • Setup Guide

The Extron CS 120P is a plenum-rated enclosure for the Extron CS 1226T SpeedMount

Ceiling Speaker System. The CS 120P

enclosure can be installed in both U.S. and metric ceiling grid systems with tiles 2 feet by 2 feet (600 mm by 600 mm) or 2 feet by

4 feet (600 mm by 1200 mm). It is UL 2043 listed for use in air handling ceiling spaces only if used in conjunction with the CS 26T

speakers.

This setup guide contains installation information about the CS 120P and provides procedures for installing it in suspended and

hard ceilings.

WARNING: Incorrect installation can result in serious injury. Installation and service must be performed by authorized

personnel only.

NOTES:

• All wiring and electrical connections must conform to all applicable building codes and local ordinances.

• Mounting must conform to all applicable building codes and local ordinances.

Installing the CS 120P Enclosure

The CS 120P enclosure must rst be mounted in the ceiling and wired for use with the CS 26T driver assembly before the CS 26T

speakers can be installed.

The minimum ceiling thickness needed to secure the speaker is 3/8 inch (0.95 cm). The maximum ceiling thickness that can be

used is 1 and 9/32 inches (3.3 cm).

For multi-trade installations, see Division of Labor Installation on page 4.

Mounting the CS 120P in a Suspended Ceiling

1. Disconnect power — Power down all attached devices.

2. Verify the space where the CS 120P will be installed — Ensure that there is sufcient clearance above the ceiling tile

for the CS 120P to rest on top of the tile.

3. Congure the CS 120P for a U.S. or metric ceiling — For U.S. ceilings (2 feet by 2 feet or 2 feet by 4 feet), leave the

four tabs on the side of the CS 120P intact. For metric ceilings (600 mm by 600 mm or 600 mm by 1200 mm), cut off the

tabs.

Tabs (4)

Removable

Tabs

4. Remove the adjacent tile — To facilitate the installation process, remove the tile adjacent to the ceiling tile where the

CS 120P will be installed.

5. Cut a hole for the CS 26T speaker. Use the provided cutout template to outline the hole to be cut in the ceiling tile as

described below.

a. Remove the ceiling tile.

b. To nd the center of the tile, use a tape measure to measure the space between two opposite corners, and mark the

half-way point.

c. Position the center hole of the cutout template directly over the center of the tile that you marked in step5b.

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

1 2 3 4

Sommario

Pagina 1 - CS 120P • Setup Guide

CS 120P • Setup GuideThe Extron CS 120P is a plenum-rated enclosure for the Extron CS 1226T SpeedMount® Ceiling Speaker System. The CS 120P enclosure

Pagina 2 - Cover Plate

d. Trace a circle on the ceiling tile as follows:For installations in ceilings that are NOT fiberglass or when installing the speakers in an open bac

Pagina 3 - Fiberglass Tile Adapter

8. Wire the CS 120P — Route the wires through the H-shaped opening in the CS 120P. Be sure to leave sufcient slack.9. Replace the terminal cover p

Pagina 4 - 68-2161-52 Rev. B

ExtronHeadquarters+800.633.9876 (Inside USA/Canada Only)ExtronUSA-West ExtronUSA-East+1.714.491.1500 +1.919.850.1000+1.714.491.1517 FAX +1.9

Commenti su questo manuale

Nessun commento

Extron-electronics CS 120P Setup Guide Manuale Utente Pagina 1

Navigare online o scaricare Manuale Utente per Hardware Extron-electronics CS 120P Setup Guide. Extron Electronics CS 120P Setup Guide User Manual Manuale Utente

Sommario

Commenti su questo manuale

Extron-electronics CS 120P Setup Guide Manuale Utente Pagina 1

Navigare online o scaricare Manuale Utente per Hardware Extron-electronics CS 120P Setup Guide. Extron Electronics CS 120P Setup Guide User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Hardware Extron-electronics CS 120P Setup Guide